Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Other

Replacement bolts for Super Logic stems. Original equipment stem hardware ensures exact fit and finish. - Replacement M5 bolts for 4-Axis stems - Includes M5*P0.8*16L x 4pcs & M5*P0.8*18L x 2pcs - Bit Size: 4mm - Thread Pitch: M5 - Length: 4x 16mm, 2x 18mm
$1.50
KMC 3/16" Master Link Chain Links - For 3/16" chain, extra wide - Extra-wide, for non-derailleur bikes: BMX, cruisers, etc - Perfectly fits on KMC 415H & 415H-NP chains
$1.95
- Aluminum straddle cable carrier for cantilever brake
$2.00 $2.99 33% Off
- Aheadset preload adjusting bolt
$3.00
- Half-link connector allows you to add or subtract half of one link (1/2 inch) from the chain in order to optimize chain tension - Uses standard chain pin connector and tool
$4.00
Eyelet Bushings for repair and maintenance of Rockshox rear shocks.
$4.00
Tools for repair and maintenance of RockShox Reverb suspension seatposts. - Specific to RockShox Reverb post
$4.25
Power Links provide tool free chain assembly. - 8-speed width: 7.1mm - 9-speed width: 6.8mm - Chain Compatibility: SRAM - Reusable: Yes
$4.25
Power links provide tool free chain assembly. - Chain Compatibility: SRAM - Reusable: No
$5.99
Compression ring fits above the upper bearing in a Cane Creek headset to ensure vertical and horizontal compression is optimal. - Compatible with 41mm and 42mm OD upper bearings
$6.50
- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity
$6.99
The Problem Solvers Cantilever Studs screw into the bosses built into bicycle frames to provide the proper mounting studs for brakes. Each brake requires two studs.
$7.00
Parts for repair and maintenance of DT Swiss hubs. - DT Swiss 240 Disc Ring Nut
$7.00
RockShox cable and hose guide.
$7.26
Hose Kits, Barbs and Strain Relief for Servicing Reverb Lines.
$7.49
Notched binder bolts for frames with integrated seat collars. Details: CroMoly steel bolts Three lengths available: 16, 19 and 21mm 8mm diameter
$7.99 - $13.85
The Problem Solvers Handlebar Clamp Shim allows you to fit almost any handlebars in almost any stem. It's machined of light and durable aluminum and grooved on the inside to hold tightly.
$8.00
- Color: Black - Length: 8.5 mm - Material: Steel - Type: Hex - Includes: 4 bolts & 4 nuts
$8.00
Replacement top caps for various RockShox suspension forks.
$8.99
The Problem Solvers Clamp-On Water Bottle Cage Mount makes it easy to carry a bottle on your handlebars so you can have even more refreshment on rides. It also comes in useful on frames without room for bottles, like smaller frames and some kid’s bikes.
$9.08
Hose Kits, Barbs and Strain Relief for Servicing Reverb Lines.
$9.95
Replacement bolts for Super Logic stems. Original equipment stem hardware ensures exact fit and finish. - Replacement T20 bolts for Super Logic stems - Includes T20-M4x15L x 4pcs & T20-M4x18L x 3pcs - Bit Size: Torx 20 - Thread Pitch: M4 - Length: 18mm (x3), 15mm (x4)
$9.95
This stem cap is where your bike fashion sense and the weight weenie in you collide. This Ultralight and ultra-sleek stem cap integrates a 5mm, 10mm or 15mm headset spacer with your stem cap in finely machined piece. Why have extra steerer tube requiring spacers on top of your stem you ask? Well, many carbon steerers require that the steer tube extend above the stem. Also, riders may want the flexibility to move handlebar height up and down for different types of riding or for bike re-sale. - Design and manufactured in Minneapolis, MN USA - 1 1/8" top (straight 1 1/8" or 1 1/2" to 1 1/8" taper) steerer tubes only - 6061-T6 aluminum - 5mm internal cylinder wall height - Black aluminum bolt included Total weight (cap + bolt): 5mm= 12g. Compare to a standard flat stem cap and steel bolt at 20 grams + spacers add even more.
$9.99
- Lower cables for Odyssey's Gyro G3 (sold separately). - Universal fit. - Lower cables only.
$9.99
- Upper cables for Odyssey's Gyro G3 (sold separately) - Universal fit. - Upper cables only.
$9.99 - $16.50
Problem Solvers has a couple different options for adding cable housing or brake hose guides to your bike. Choose from the adhesive stick-on option or the guide that mounts to existing housing stops.
$9.99
The Problem Solvers Seatpost Shim is what you need when your seatpost is a little too small-diameter to fit tightly into your frame. It's made of light, durable aluminum and has a lip on the top so it won't slide down inside the frame during installation.
$9.99
Switching frames doesn’t mean you have to switch posts! Use your old posts without worry with Problem Solver's wide variety of seatpost shims. -100mm long -3mm lip -Alloy Problem Solvers Seatpost Shims are not intended for use with carbon seatposts
$10.00
Consider this the cherry on top of your sundae. Pull the whole thing together with an All-City top cap. - Includes star nut
$10.00
Service your DT Swiss star ratchet hubs and wheels with DT Swiss Ratchet and Kits. - DT Swiss Service Kit - 3-Pawl
$10.00
Keep the weight down and your headset snug with the Specialzied Carbon Steerer Tube Plug.
$10.00
One of the coolest things about Surly is if they can't find an existing part that fits their standards, they just make one themselves. This cable hanger is made to fit around the oversize bolt on their Constrictor seatpost clamp so you can be sure it will fit around almost any other seatpost clamp bolt too. It comes complete with an adjusting barrel.
$10.50
40-Series Bearing - Compatible with 110-, 40-, and 10-Series headsets
$11.00
- GX Eagle Rear Derailleur B-Bolt and Limit Screw Kit Hex5
$12.00
FSA bearings that set directly into the frame without the use of pressed in cups. - 36/45 degrees is Cane Creek-compatible - 45/45 degrees is Campagnolo-compatible
$13.99
DEITY Grip Clamps offer a way to customize your bike to match your style.
$13.99
- Wears and functions like other links on the chain - SIL-TEC surface treatment - Tool free installation possible - TL-CN10 is available as SM-CN900-11 - Single use
$14.18
Bottom bracket cup and spindle spacers for adjusting chainline or bearing play.
$17.00
These are the correct connecting links for SRAM's 12-speed Eagle chains. They are great for installing new chains and fixing chains on the road and trail, too. They come in a four pack, for use with four chains.
$17.99
The Problem Solvers Compression Plug for 1 1/8-inch Forks is for threadless aluminum and carbon forks. It fits tightly inside the fork and provides easy headset adjustment and a nice, clean look.
$18.00 - $23.00
Disc brake mount adaptor. - Includes stainless steel adaptor and caliper bolts
$18.00
If you put in a lot of miles and/or sweat a lot, your shifter hoods probably need freshening up. Grab a pair of Shimano Dura-Ace STI Lever Hoods to make your bike feel new again. - Fits Dura-Ace ST-R9100 levers
$19.00
The Hope Tech 3 Duo Shifter Mounts help to keep the cockpit neat and tidy, while integrating with the rest of your controls. - This direct mount for Tech 3 Duo master cylinders will fit all SRAM shifters with a removable clamp - Crafted from machined aluminum
$19.99
Problem Solvers Pog top caps are machined aluminum with a 5 or 10mm spacer integrated as one piece. This makes for a clean, finished look when mounting a stem below the top of the steerer tube. - Bolt not included - 10mm available with or without logo - 5mm available without logo only
$20.00
Rebuild seal kits for Fox rear suspension service and repair. - Includes parts needed for rebuild
$20.00
- SRAM, Road pulleys, 11.7515.060.000
$21.95
Roadlink Rear Derailleur Part - The RoadLink is optimized for use with ten or eleven-speed 11-36t and 11-40t cassettes - 11-42 or 10-42 setups are not supported - Works with all 10-11 speed Shimano and SRAM Road Derailleurs - Best used with Single or Double Setups - see manufacturer's site for more details
$21.99
In true DEITY fashion, the Crosshair Headset Cap exemplifies the style and detail you've come to expect from everything DEITY offers. We've included 3mm, 5mm, and 8mm spacers that are color-matched to create a clean refined option to finish off your cockpit. Not only are the cap and spacers machined from 6061 Aluminum, the bolt is CNC Machined from 7075 Aluminum to give you a precise and extremely durable centerpiece that is truly hassle-free. - Complete Aluminum 1 1/8" Headset Cap Kit - Features 7075 T6 Machined Aluminum Bolt - Includes 3mm, 5mm, and 8mm Spacers - Spacers Feature a Thin Profile For a Minimalist Style - Countersunk Bolt Design - Kit Includes the Star Nut - Weight: 13 grams (without star nut)
$22.00
Replacement headset bearings from FSA. - Compatible with most Trek MTB integrated headset systems - Sealed bearing for long life - Compatible with Knock Block Headsets
$22.00
Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA
$22.00
Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA
$22.00
Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA
$22.00
Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - CNC machined 6061 aluminum - Black anodized finish - Made in the USA
$22.00
Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA
$22.00
Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA
$22.00
Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA
Page 1 of 3 Next page